$ sudo smartctl -a /dev/sda [sudo] password for sun: smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD1600BEVT-22ZCT0 Serial Number: WX91A8458218 Firmware Version: 01.01A01 User Capacity: 160 041 885 696 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Thu May 15 16:59:23 2014 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (3600) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 46) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7037) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 7 3 Spin_Up_Time 0x0027 186 186 021 Pre-fail Always - 1666 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 88 5 Reallocated_Sector_Ct 0x0033 154 154 140 Pre-fail Always - 503 7 Seek_Error_Rate 0x002f 100 253 051 Pre-fail Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 45 10 Spin_Retry_Count 0x0033 100 253 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 88 184 Unknown_Attribute 0x0033 100 100 000 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 064 060 000 Old_age Always - 36 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 48 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 39 194 Temperature_Celsius 0x0022 111 107 000 Old_age Always - 36 195 Hardware_ECC_Recovered 0x0036 200 200 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0032 168 168 000 Old_age Always - 32 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0 SMART Error Log Version: 1 Warning: ATA error count 69 inconsistent with error log pointer 3 ATA Error Count: 69 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 69 occurred at disk power-on lifetime: 41 hours (1 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 45 45 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 03 45 00 00 00 a0 08 00:02:16.791 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 08 00:02:16.782 IDENTIFY DEVICE ec 00 00 00 00 00 a0 08 00:02:11.647 IDENTIFY DEVICE ef 03 45 00 00 00 a0 08 00:02:11.640 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 08 00:02:11.631 IDENTIFY DEVICE Error 68 occurred at disk power-on lifetime: 41 hours (1 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 45 45 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 03 45 00 00 00 a0 08 00:02:11.640 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 08 00:02:11.631 IDENTIFY DEVICE ec 00 00 00 00 00 a0 08 00:02:06.519 IDENTIFY DEVICE ef 03 45 00 00 00 a0 08 00:02:06.513 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 08 00:02:06.479 IDENTIFY DEVICE Error 67 occurred at disk power-on lifetime: 41 hours (1 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 45 45 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 03 45 00 00 00 a0 08 00:02:06.513 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 08 00:02:06.479 IDENTIFY DEVICE ca 00 80 08 5c 14 e0 08 00:02:05.541 WRITE DMA ec 00 00 00 00 00 a0 08 00:02:05.532 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 00:02:05.525 SET FEATURES [Set transfer mode] Error 66 occurred at disk power-on lifetime: 41 hours (1 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 80 45 5c 14 e0 Device Fault; Error: ABRT at LBA = 0x00145c45 = 1334341 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 80 08 5c 14 e0 08 00:02:05.541 WRITE DMA ec 00 00 00 00 00 a0 08 00:02:05.532 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 00:02:05.525 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 08 00:02:05.517 IDENTIFY DEVICE ca 00 08 00 5c 14 e0 08 00:02:05.517 WRITE DMA Error 65 occurred at disk power-on lifetime: 41 hours (1 days + 17 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 46 45 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 03 46 00 00 00 a0 08 00:02:05.525 SET FEATURES [Set transfer mode] ec 00 00 00 00 00 a0 08 00:02:05.517 IDENTIFY DEVICE ca 00 08 00 5c 14 e0 08 00:02:05.517 WRITE DMA ec 00 00 00 00 00 a0 08 00:02:05.508 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 00:02:05.501 SET FEATURES [Set transfer mode] SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.